Detections
Analytics

CISC-RT-000440 - The Cisco out-of-band management (OOBM) gateway router must be configured to block any traffic destined to itself that is not sourced from the OOBM network or the Network Operations Center (NOC).

Warning! Audit Deprecated

This audit has been deprecated and will be removed in a future update.

View Next Audit Version

Information

If the gateway router is not a dedicated device for the OOBM network, several safeguards must be implemented for containment of management and production traffic boundaries. It is imperative that hosts from the managed network are not able to access the OOBM gateway router.

NOTE: Nessus has provided the target output to assist in reviewing the benchmark to ensure target compliance.

Solution

This requirement is not applicable for the DODIN Backbone. It is only applicable if the OOBM gateway router is not a dedicated device to the OOBM backbone.

Step 1: Configure the ACL to only allow traffic to the route processor from the OOBM backbone and the NOC.

R4(config)#ip access-list extended TRAFFIC_FROM_NOC
R4(config-ext-nacl)#permit ip 10.11.1.0 0.255.255.255 host 10.11.1.8
R4(config-ext-nacl)#permit ip 10.12.1.0 0.255.255.255 host 10.11.1.8
R4(config-ext-nacl)#permit ip 10.11.1.0 0.255.255.255 host 10.13.1.1
R4(config-ext-nacl)#permit ip 10.12.1.0 0.255.255.255 host 10.13.1.1
R4(config-ext-nacl)#deny ip any host 10.11.1.8 log-input
R4(config-ext-nacl)#deny ip any host 10.13.1.1 log-input
R4(config-ext-nacl)#permit ip 10.11.1.0 0.0.0.255 10.13.1.0 0.0.0.255
R4(config-ext-nacl)#permit ip 10.12.1.0 0.0.0.255 10.13.1.0 0.0.0.255
R4(config-ext-nacl)#deny ip any any log-input

 Step 2: Configure the ACL to only allow traffic to the route processor from the OOBM LAN.

R4(config)#ip access-list extended TRAFFIC_TO_NOC
R4(config-ext-nacl)#permit ip 10.13.1.0 0.255.255.255 host 10.13.1.1
R4(config-ext-nacl)#permit ip 10.13.1.0 0.255.255.255 host 10.11.1.8
R4(config-ext-nacl)#deny ip any host 10.13.1.1 log-input
R4(config-ext-nacl)#deny ip any host 10.11.1.8 log-input
R4(config-ext-nacl)#permit ip 10.13.1.0 0.255.255.255 10.11.1.0 0.0.0.255
R4(config-ext-nacl)#permit ip 10.13.1.0 0.255.255.255 10.12.1.0 0.0.0.255
R4(config-ext-nacl)#deny ip any any log-input
R4(config-ext-nacl)#exit

Step 3: Apply the ACLs configured above to the appropriate OOBM interfaces as shown in the example below.

R4(config)#int g0/2
R4(config-if)#ip access-group TRAFFIC_FROM_NOC in
R4(config)#int g0/3
R4(config-if)#ip access-group TRAFFIC_TO_NOC in
R4(config-if)#end

See Also

https://dl.dod.cyber.mil/wp-content/uploads/stigs/zip/U_Cisco_IOS_Router_Y23M10_STIG.zip

Item Details

References: CAT|II, CCI|CCI-001097, Rule-ID|SV-216592r531085_rule, STIG-ID|CISC-RT-000440, STIG-Legacy|SV-105723, STIG-Legacy|V-96585, Vuln-ID|V-216592

Plugin: Cisco

Control ID: 68fbb71c94e693e27d22fd2834785d5f209c675f09b190d9c7931f4ff7d49d52