CISC-RT-000120 - The Cisco router must be configured to protect against or limit the effects of denial-of-service (DoS) attacks by employing control plane protection.

Information

The Route Processor (RP) is critical to all network operations because it is the component used to build all forwarding paths for the data plane via control plane processes. It is also instrumental with ongoing network management functions that keep the routers and links available for providing network services. Any disruption to the RP or the control and management planes can result in mission-critical network outages.

A DoS attack targeting the RP can result in excessive CPU and memory utilization. To maintain network stability and RP security, the router must be able to handle specific control plane and management plane traffic that is destined to the RP. In the past, one method of filtering was to use ingress filters on forwarding interfaces to filter both forwarding path and receiving path traffic, as well as limiting traffic destined to the device. However, this method does not scale well as the number of interfaces grows and the size of the ingress filters grows. Control plane policing increases the security of routers and multilayer switches by protecting the RP from unnecessary or malicious traffic. Filtering and rate limiting the traffic flow of control plane packets can be implemented to protect routers against reconnaissance and DoS attacks, allowing the control plane to maintain packet forwarding and protocol states despite an attack or heavy load on the router or multilayer switch.

Solution

Configure the Cisco router to protect against known types of DoS attacks on the route processor. Implementing a CoPP policy as shown in the example below is a best practice method.

Step 1: Configure ACLs specific traffic types.

R1(config)#ip access-list extended CoPP_CRITICAL
R1(config-ext-nacl)#remark our control plane adjacencies are critical
R1(config-ext-nacl)#permit ospf host x.x.x.x any
R1(config-ext-nacl)#permit ospf host x.x.x.x any
R1(config-ext-nacl)#permit pim host x.x.x.x any
R1(config-ext-nacl)#permit pim host x.x.x.x any
R1(config-ext-nacl)#permit igmp any 224.0.0.0 15.255.255.255
R1(config-ext-nacl)#permit tcp host x.x.x.x eq bgp host x.x.x.x
R1(config-ext-nacl)#deny ip any any
R1(config-ext-nacl)#exit

R1(config)#ip access-list extended CoPP_IMPORTANT
R1(config-ext-nacl)#permit tcp host x.x.x.x eq tacacs any
R1(config-ext-nacl)#permit tcp x.x.x.x 0.0.0.255 any eq 22
R1(config-ext-nacl)#permit udp host x.x.x.x any eq snmp
R1(config-ext-nacl)#permit udp host x.x.x.x eq ntp any
R1(config-ext-nacl)#deny ip any any
R1(config-ext-nacl)#exit

R1(config)#ip access-list extended CoPP_NORMAL
R1(config-ext-nacl)#remark we will want to rate limit ICMP traffic
R1(config-ext-nacl)#deny icmp any host x.x.x.x fragments
R1(config-ext-nacl)#permit icmp any any echo
R1(config-ext-nacl)#permit icmp any any echo-reply
R1(config-ext-nacl)#permit icmp any any time-exceeded
R1(config-ext-nacl)#permit icmp any any unreachable
R1(config-ext-nacl)#deny ip any any
R1(config-ext-nacl)#exit

R1(config)#ip access-list extended CoPP_UNDESIRABLE
R1(config-ext-nacl)#remark management plane traffic that should not be received
R1(config-ext-nacl)#permit udp any any eq ntp
R1(config-ext-nacl)#permit udp any any eq snmp
R1(config-ext-nacl)#permit tcp any any eq 22
R1(config-ext-nacl)#permit tcp any any eq 23
R1(config-ext-nacl)#remark control plane traffic not configured on router
R1(config-ext-nacl)#permit eigrp any any
R1(config-ext-nacl)#permit udp any any eq rip
R1(config-ext-nacl)#deny ip any any
R1(config-ext-nacl)#exit
R1(config)#ip access-list extended CoPP_DEFAULT
R1(config-ext-nacl)#permit ip any any
R1(config-ext-nacl)#exit

Step 2: Configure class maps referencing each of the ACLs.

R1(config)#class-map match-all CoPP_CRITICAL
R1(config-cmap)#match access-group name CoPP_CRITICAL
R1(config-cmap)#class-map match-any CoPP_IMPORTANT
R1(config-cmap)#match access-group name CoPP_IMPORTANT
R1(config-cmap)#match protocol arp
R1(config-cmap)#class-map match-all CoPP_NORMAL
R1(config-cmap)#match access-group name CoPP_NORMAL
R1(config-cmap)#class-map match-any CoPP_UNDESIRABLE
R1(config-cmap)#match access-group name CoPP_UNDESIRABLE
R1(config-cmap)#class-map match-all CoPP_DEFAULT
R1(config-cmap)#match access-group name CoPP_DEFAULT
R1(config-cmap)#exit

Step 3: Configure a policy map referencing the configured class maps and apply appropriate bandwidth allowance and policing attributes.

R1(config)#policy-map CONTROL_PLANE_POLICY
R1(config-pmap)#class CoPP_CRITICAL
R1(config-pmap-c)#police 512000 8000 conform-action transmit exceed-action transmit
R1(config-pmap-c-police)#class CoPP_IMPORTANT
R1(config-pmap-c)#police 256000 4000 conform-action transmit exceed-action drop
R1(config-pmap-c-police)#class CoPP_NORMAL
R1(config-pmap-c)#police 128000 2000 conform-action transmit exceed-action drop
R1(config-pmap-c-police)#class CoPP_UNDESIRABLE
R1(config-pmap-c)#police 8000 1000 conform-action drop exceed-action drop
R1(config-pmap-c-police)#class CoPP_DEFAULT
R1(config-pmap-c)#police 64000 1000 conform-action transmit exceed-action drop
R1(config-pmap-c-police)#exit
R1(config-pmap-c)#exit
R1(config-pmap)#exit

Step 4: Apply the policy map to the control plane.

R1(config)#control-plane
R1(config-cp)#service-policy input CONTROL_PLANE_POLICY
R1(config-cp)#end

Item Details

Audit Name: DISA STIG Cisco IOS Router RTR v3r1

Category: SYSTEM AND COMMUNICATIONS PROTECTION

Plugin: Cisco

Control ID: 310f062709ecd8d1c7fc01f3ee653a962fac2c8fd9c9b183d7e3be53a56d5952

Detections

Analytics

CISC-RT-000120 - The Cisco router must be configured to protect against or limit the effects of denial-of-service (DoS) attacks by employing control plane protection.

Information

Solution

See Also

Item Details